| MODEL
D20R SINGLE-DOUBLE MITRE SAW |
| |
| |
Standard
machine equipped as follows: 12” Blade capacity; 1 H.P.
1 Phase 110 Volt TEFC Motors, NEMA 56 Frame with toggle switch
and cord for each motor which draws 15 amps; completely enclosed
2-belt drive, Rotating Blade Guard and Dust Outlets; steel
ground base; heads fixed at 45O to front fence; mounted on
a Floor Strand with dust blades are not
included |
$3,35.00 |
| |
D20R
Package includes machine on Floor Stand, and Extended
Table Work Support, and one pair of 12 x 100 Tooth Carbide
Blades for metal and/or wood |
$3,95.00 |
| |
|
|
| MODEL
D45FX FOOT OPERATED FIXED HEAD DOUBLE MITRE SAW |
| |
|
|
| |
Standard
machine equipped exactly the same Model D45AX below, except
that actuation is by Manual Foot Petal |
$4,775.00 |
| |
|
|
| MODEL
D45AX FIXED HEAD DOUBLE MITRE SAW |
|
| |
|
|
| |
Standard
machine equipped as follows: 10” Blade Capacity
standard, 12” & 14” Blade Capacity available;
1-1/2 H.P. 1 Phase 220 Volt or 3 Phase 220/440 TEFC Motors,
NEMA 56 Frame; 2-belt drive with Dual Magnetic Starter; rotary
cam disconnect switch, and an interlock switch on the blade
guard; adjustment for blade variation allows precision alignment
of blades to minimize scrap; saw heads adjustable up to 30
for assurance of perfect mitres; 35” high table of heavy
cast iron; floor stand completely enclosed with 6” dust
collector outlet, includes scrap chute; keyed fences, adjustable
front to rear; precision machined and ground saw arm; pivot
brackets and table, with milled slots to guide pivot brackets
and fences; 2” diameter air cylinder with adjustments
for speed, stroke length, and position of blade above work;
actuation by pneumatic spring return foot valve; air filter/regulator/lubricator
with auto drain……………................................................................................ |
$5,650.00 |
| |
|
|
| MODEL
N90 VERTICAL FRAME AND NOTCHING SAW |
|
| |
|
|
| |
Standard
machine equipped as follows: 16” Blade Capacity;
3 H.P. 3 Phase 230/460 Volt TEFC Motors, NEMA 182 Frame; 2-belt
drive with dual Magnetic Starter; rotary cam disconnect switch,
and an interlock switch on the blade guard; 1” saw arbor
and 3-1/2” saw collars; floor and stand enclosed with
6” dust outlet, includes scrap chute, precision ground
heavy cast base; blades move vertically on hardened rods,
3” diameter air cylinder actuated by a foot valve; air
filter/regulator/lubricator with auto drain; with Chip Breaker. |
|
| |
Specify
either Non-Staggered Blade Mitering
Machine or Staggered Blade Notching
Machine |
$9,295.00 |
| |
Special
18” Staggered Blade Toe Notching Machine |
$10,195.00 |
| |
|
|
| OPTIONAL
MOTORS – REPLACE STANDARD MOTORS AND ELECTRICS. |
| |
|
|
|
| |
50C
|
1-1/2 H.P.
1 or 3 Phase 220 Volt TEFC 50HZ Motors, 2950 RPM for D45AX,
D45FX & D20R…................................................…. |
$
100.00 |
| |
50C |
For standard
Motors on Models N80 and N90…......................... |
$
250.00 |
| |
2H1 |
2 H.P.
1 Phase 220 Volt TEFC 60 HZ Motors, 3450 RPM; for 10:, 12: or
14” machines……................................................……... |
$
200.00 |
| |
2H3
|
2 H.P.
3 Phase 220 Volt TEFC 60 HZ Motors, 3450 RPM for D45AX &
D45FX, for 10” or 12” machines
(standard on 14” machines)
|
$
120.00 |
| |
3H3 |
3 H.P.
3 Phase 220/440 Volt TEFC 60 HZ, 3450 RPM-For Model N80 only……………...............................................……………. |
$
150.00 |
| |
5H3 |
5 H.P.
3 Phase 220/440 Volt TEFC 60 HZ, 1725 RPM-For model N90 only…………………………................................................ |
$
300.00 |
| |
575V |
575 Volt;
Standard Motors for machine; NEMA 12 Dust Proof Enclosure…….........................................……………………….. |
$
550.00 |
| |
|
|
|
| ADDITONAL
OPTIONAL ACCESSORIES |
|
| |
|
|
|
| |
12”/D45
|
12”
Blade Capacity - For Models D45AX and D45FX
only…….. |
$
120.00 |
| |
14”HT
|
14”
Blade Capacity - For Models D45AX and D45FX only
(standard with 2 H.P. 3 Phase motor) |
$
450.00 |
| |
SLS |
SAWBLADE LUBRICATION SYSTEM - For
lubricating blades when cutting non-ferrous material; Requires
compressed air; includes vacuum pump, nozzle, hoses and fittings,
container and check valve |
|
| |
|
MODEL
D20 - Includes two Automatic Valves…….…………….… |
$ 385.00 |
| |
|
MODEL
D45FX - Includes Automatic Valve………………….….... |
$ 295.00 |
| |
|
MODEL
D45AX - Includes Automatic Valve…………...…….….... |
$ 250.00 |
| |
|
|
|
| |
BIOL |
CTD
BIOLUBE LUBRICATION SYSTEM - Uses a pump system to
lubricate blades; system uses a minute amount of high-grade
biodegradable oil per cycle; flow rate adjustable; includes
air filter and one pint of lubricant………................................................. |
$1,125.00 |
| |
|
|
|
| |
B3P141 |
CTDBIOLUBE
LUBRICANT - per gallon……………………........... |
$
60.00 |
| |
HYD |
HYDROCHECK
UNIT - Provides smoother slow-speed action cutting
heavy extrusions or hardwoods; for Model D45AX only….. |
$
795.00 |
| |
VC3 |
VERTICAL
AIR CLAMP - 3” stroke; easy height and position
adjustment; auto release (each) |
$
165.00 |
| |
SHC |
SPECIAL
45o HORIZONTAL PNEUTAMIC CLAMPS - Clamps materials
close to blade at 45o to front fence, Provides one times line
pressure; Not available for Model D20R……….......……(each)
|
$
225.00 |
| |
|
|
|
| |
AV |
AUTOMATIC
VALVE - for actuation of clamps when purchased without
SLS for D20R and D45FX |
$
95.00 |
| |
PR |
PRESSURE
REGULATOR - For adjustment of clamping pressure on
all pneumatic clamps……………......................................... |
$
75.00 |
| |
SOL |
WATER
SOLUABLE OIL - Use with Spray Mist Applications; Mix
10 parts water to one part oil. per gallon………………………...... |
$
18.00 |
| |
FMF |
FRONT
MITERING FENCES - To convert staggered blade notching
machine to mitering machine; Must add Length Gages for measurement;
For Model N80 and Model N90 only
(Front mount)………….............................................................
|
$
175.00 |
| |
|
(Rear mount)…………………………………………………………… |
$
295.00 |
| |
REV/FHC |
Special
front mount Horizontal Clamp with reverse fences for cutting
parts shorter than 5” long …..Consult factory
for additional information……………………………………….............………from |
$
650.00 |
| |
COL |
DUST
COLLECTOR UNITS - 3 H.P……………………………….... |
$
650.00 |
| |
CB |
CHIP
BREAKER - For model D45AX and D45FX only; helps eliminate
tear out of delicate wood moulding or double sided laminate
materials; Standard on Models & N80 & N90……………
|
$
95.00 |
| |
|
|
|
| MEASURING
GAGES: |
|
| |
|
|
|
| |
FEX |
FRONT
EXTENDED FENCE LENGTH GAGE - 5/8” X 2”
high fence with measuring tape, stop, and clamp; measures mitre
dimension………………………………………….......……….6’
long
|
$
205.00 |
| |
|
…………………………………………………………........…10’
long |
$
295.00 |
| |
|
|
|
| |
REX |
REAR
EXTENDED FENCE LENGTH GAGE - Stock is held in front
of fence and can be easily removed to front machine; same
as item FEX, but reversed; used for production measurement
of particular extrusion or moulding; not available for Model
D20R 6’ long………
|
$
275.00 |
| |
|
|
|
| |
SWS |
SWING
STOP - Multiple stops used for preset dimensions.
All stops automatically swing out to stop material. Stop retracts
by pushing against it……………….6
foot fence includes three stops |
$
450.00 |
| |
|
..............................................10
foot fence includes four stops |
$
575.00 |
| |
|
ADDITONIAL
SWING STOP (part No. 200BE50)…………………… |
$
75.00 |
| |
|
|
|
| |
VIS |
VISION
GAGE: For measuring inside, rabbet or outside dimension
of moulding. Lines are printed on 45o to front fence in three
different colors in 1/8” increments. Stainless steel
gage is made for right hand mounting only and measures 6”
wide material; includes table work support.
6’ long……………...................................................................
|
$1,075.00 |
| |
|
10’
long…..………................................................................... |
$1,695.00 |
| |
|
|
|
| |
OMD |
OUTSIDE
MEASURING DEVICE: An accurate screw is fastened to
a 5/8” front fence. A screw meshes in 1/16” or
1mm graduations. A flip of a lever releases locking screw,
and stop is easily moved from 4” within +/- .010. Simplifies
and speeds up length changes on outside dimensions of materials.
– Requires hand mount item T60 or T10.
Right hand mount only 6’ long….................……………….………
|
$
495.00 |
| |
|
10’
long….................……………………… |
$
695.00 |
| |
OMD/RAB |
Combination
of Gages OMG and RAB;
6 foot long……………………………...........................................
|
$
595.00 |
| |
OMD/RAB |
Combination
of Gages OMG and RAB;
10 foot long……………............................................................
|
$
795.00 |
| |
|
|
|
| |
RAB |
RABBET
MEASURING SYSTEM: Measures inside rabbet of frame
directly in any position, front to rear. A slide is keyed
to the base, which moves in a line with the blade. Fixed to
slide is an aluminum angle with a measuring tape. All conventional
moulding are easily measured. Locates both outside and rabbet
measurement of mouldings. Includes item FEX Front Extended
Fence Length Gage (standard on Model D20R). Requires table
support item T60 orT10. |
|
| |
|
For Models
D45AX and D45FX ............................... 6’ long
fence |
$
295.00 |
| |
|
...........................................................................10’
long fence |
$
395.00 |
| |
|
Models
D22-30, N80 & N90...................................
6’ long fence |
$
395.00 |
| |
|
...........................................................................10’
long fence |
$
495.00 |
| |
|
RAB for
D20R 10’ long (6’ long RAB standard on D20R)..……...... |
$
150.00 |
| |
|
|
|
| |
DIG/LEN |
Digital
Length measurement fence--for point to point only……………………….....................................,………6’
length |
$1,395.00 |
| |
|
Item Length
FEX with Digital Measuring Scale & Display……………………………..….............................10’
length |
$1,750.00 |
| |
|
|
|
| |
ARS |
AIR
STOP............................................................................... |
$
265.00 |
| |
|
|
|
| EXTENDED
TABLEWORK SUPPORTS: |
|
| |
|
|
|
| |
T60 |
EXTENDED
TABLE WORK SUPPORT - 10” wide x 60” long
with leg; used for infeed and outfeed material supports……………...... |
$
205.00 |
| |
T10 |
EXTENDED
TABLE WORK SUPPORT - 10” wide X 10’ Long
with two legs………………………… |
$
295.00 |
| |
RC |
ROLLER
CONVEYOR - 11-1/2” wide rollers x 10’ long
attached to Floor Stand with leg and 7 rollers …………………………............. |
$
450.00 |
| |
|
with PVC
Rollers add……………………………………………........ |
$
140.00 |
| |
|
|
|
| OTHER
OPTIONAL ACCESSORIES: |
|
| |
|
|
|
| |
FLP/D45 |
PRODUCTION
FLIPPERS STOP - For multiple gaging; for use with item
OMD, Outside Measuring Devise only………….............
|
$
95.00 |
| |
CTR |
PNEUMATIC
STROKE COUNTER - Counts each stroke of sawheads……………………………............................................ |
$
295.00 |
| |
|
|
|
